Vacant Unit Utility Costs: How to Manage Them at Turnover
Owners pay utilities whenever a unit sits vacant. Control the cost with exact move dates, a low-use baseline, leak alerts and bill-backs inside lease dates.

When a unit is vacant, the owner pays its utilities. To manage that cost, record the exact move-out and move-in dates, keep service on in the owner's name between residents, hold use to a low baseline, investigate anything above it, and bill back any use that falls inside a resident's lease dates.
Vacancy is a small share of unit-months and a disproportionate share of utility surprises. This guide covers where the cost comes from and a turnover process that contains it.
Who pays for utilities in a vacant unit?
The owner does. Where residents hold their own utility accounts, the account closes or transfers at move-out and the owner becomes responsible until the next resident opens one. Where the property is master-metered, the owner was paying all along, and vacancy removes the resident who was reimbursing a share.
Many utilities offer landlord or continuous service arrangements that move an account into the owner's name automatically when a resident closes it, so service is not shut off between residents. Ask each provider what it offers and what it costs. Without one, a unit can lose power or water during make-ready, and restoring it takes time.
How large is the exposure?
The US Census Bureau reported a national rental vacancy rate of 7.6 percent for the third quarter of 2026. Source: Census Bureau, Housing Vacancies and Homeownership.
That figure is a national average for all rental housing and yours will differ. Multiply your own vacant unit-days by your average daily utility cost for an empty unit to size the line for your portfolio. If you cannot produce that daily cost today, that is the first gap to close.
Why do vacant units still use utilities?
An empty unit should use very little. When it uses more, the cause is usually one of four things.
- Leaks. Nobody is home to notice. The Environmental Protection Agency says the average household's leaks can account for more than 9,300 gallons of water wasted each year, and that nine percent of homes have leaks that waste 50 gallons or more per day. A faucet dripping once per second wastes more than 3,000 gallons a year. Source: EPA WaterSense, Fix a Leak Week.
- Heating and cooling left at occupied settings. A thermostat left where the last resident set it runs for no one. Keep enough heat in cold weather to protect pipes, and check your insurer's requirements for vacant property.
- Make-ready work. Painters, cleaners and carpet crews use power and water. This use is expected, and it should end when the work does.
- Irrigation and exterior use. The EPA notes that an irrigation leak about 1/32 of an inch wide can waste about 6,300 gallons a month.
Water is the utility to watch. A leak in an occupied home gets reported. In a vacant one it runs until the bill arrives.
How should you handle utilities at turnover?
- Record the move-out date and a meter reading. Photograph the meter where you can. The date decides who pays for which days.
- Confirm the account has moved to the owner. Check with each provider. Do not assume the continuous service arrangement worked.
- Set the unit to vacant settings. Adjust the thermostat, turn the water heater to its lowest or vacation setting, and shut off irrigation that is not needed.
- Inspect for leaks on day one. Check toilets, faucets, the water heater and hose bibs during the move-out inspection.
- Set a vacant baseline. Decide what an empty unit of that type should use per day, by utility.
- Review every bill against the baseline. Any vacant-period bill above it gets a work order before it gets paid.
- Record the move-in date and reading. Then confirm the new resident has opened an account or been added to billing from the lease start date.
- Prorate the split bill. A bill that spans the move date is divided by days or by the readings.
Steps 2 and 7 are where money is lost. An account that never left the owner's name means the owner keeps paying a resident's usage for months without knowing it.
What is vacant unit cost recovery?
Vacant unit cost recovery is the process of finding utility use that the owner paid for but that occurred while a resident held the lease, and billing it back to that resident. It applies where the lease makes the resident responsible for utilities from the lease start date.
| Period | Who bears the cost | What to check |
|---|---|---|
| Lease active, resident account open | Resident, directly | Nothing to recover |
| Lease active, account still in owner's name | Resident, by bill-back | Lease language, lease dates, bill service dates |
| Between leases | Owner | Use against the vacant baseline |
| Bill spans a move date | Split | Proration method stated in the lease |
Recovery depends on three records lining up: the lease dates, the service dates on the bill, and the date the resident's own account opened. With all three, the charge is easy to explain. Without them, it becomes a dispute.
Rules on billing utilities to residents vary by state and city, and affordable housing programs add their own limits. Check what your lease and local law allow, including any fees, before you bill back.
Which numbers should you track?
- Vacant days per unit, from the lease record.
- Utility cost per vacant day, by utility.
- Count of units where the account did not transfer on time at move-in.
- Dollars identified for recovery and dollars collected.
- Vacant-period bills above baseline, and how many led to a repair.
Review these monthly by property. A property with high cost per vacant day usually has a make-ready or leak problem. A property with many late transfers has a leasing process problem.
How AirBills handles it
AirBills tracks occupancy status by property and alerts on vacancy changes, cost spikes and late bills. It manages continuous service agreements, showing which properties each agreement covers, how many are vacant and the average days vacant between residents. Each bill is split between resident and owner by occupancy, with proration around move dates. In our PadSplit case study, an abnormal water reading on a vacant property was flagged the day the statement arrived. See AirBills for property managers.