What Is Utility Submetering?
Utility submetering puts an owner-installed meter on each unit behind the master meter, so residents pay for measured use. How it works and what to check.

Utility submetering means installing an owner-owned meter on each unit or space behind the utility's master meter. The utility still sends one bill for the whole property. The submeters record what each unit used, and the owner bills each resident or tenant for that measured share.
Submetering is the main alternative to allocating a master bill by formula. This guide covers what a submeter is, what it changes, and what to check before you install or bill.
What is utility submetering?
The US Environmental Protection Agency describes submetering as the use of facility-owned metering equipment to measure a subset of total use, such as individual buildings, tenant spaces or specific water-intensive activities. In most cases a submeter does not need its own utility account, so it does not add meter connection fees or ongoing utility meter charges. Source: EPA WaterSense at Work, Metering and Submetering (November 2023).
The National Conference of State Legislatures gives a billing-focused definition: meters installed behind the utility's main meter so the operator of a multi-unit property can bill each unit for its own usage. Source: NCSL, Utility Submetering.
Water, electricity and gas can all be submetered. Trash and stormwater cannot, because there is nothing at the unit to measure.
How is a submeter different from a master meter?
| Question | Master meter only | Submeter per unit | Utility meter per unit |
|---|---|---|---|
| Who owns the meter | The utility | The property owner | The utility |
| Who holds the utility account | The owner | The owner | Each resident |
| Who bills the resident | The owner, by formula or in rent | The owner, by measured use | The utility |
| Basis of the resident's bill | An allocation such as square footage | That unit's reading | That unit's reading |
EPA notes that multifamily properties typically have one master meter for a building or property unless the water utility or local authority requires unit metering, or the owner plans to submeter each unit for billing. To be separately metered by the utility, each unit must be a wholly separate plumbing system attached to the main line. Source: EPA WaterSense, Metering technical sheet.
Billing a master bill by formula is called ratio utility billing. We compare the two approaches in RUBS in 2026.
Does submetering reduce consumption?
For water, the evidence says yes. EPA's metering technical sheet cites a national study of multifamily buildings in which residents of submetered units used approximately 15 percent less water than residents of unmetered units.
EPA lists other uses for submeter data beyond billing. Owners can use it to find and respond to leaks quickly, allocate costs to tenants properly, benchmark building water use, and measure the results of efficiency projects. A unit-level reading also shows which unit has the running toilet, which a master meter cannot.
What should you plan before installing submeters?
EPA's guidance for multifamily builders and managers includes these points:
- Decide early. Investigate submetering while the plumbing system is being designed.
- Supply each unit from a single pipe. One supply line per unit is less expensive to meter than several lines entering the same unit.
- Choose the right meter. Positive displacement meters can suit residential use because they are accurate at low flows.
- Size the meter correctly. Size depends on the unit's fixtures, expected occupancy and peak demand.
- Install where it can be read and repaired. The location should be accessible and protected from weather and damage.
- Add a strainer. A strainer on the inlet keeps debris and sediment out of the meter.
Existing buildings are harder. Where several supply lines feed one unit, a retrofit may need more than one meter per unit, and the cost can outweigh the benefit.
What do regulations say about submetering?
Rules differ by state and sometimes by city. NCSL's summary, last updated in January 2016, counted 22 states, three counties and Washington, D.C. with statutes, regulations or rulings on submetering. It notes that some states regulate water and electric submetering differently, and that rules on fees vary widely. Check the current rule in your state, because the count is ten years old.
Texas shows how detailed a rule can be. For apartment electric submetering, the Public Utility Commission's rule requires that submetered charges stay separate from rent, that the owner bill at the average cost per kilowatt-hour with no extra charges, and that the bill state it is not from the utility. Owners must keep readings and tenant billings for the current month and the 12 preceding months, and test submeters at least annually. Source: 16 Tex. Admin. Code § 25.142.
EPA gives the same advice in general terms: some states or utilities require submeters for individual units, and others require approval from a state agency or utility commission before submeters are installed. Before you start, check:
- Whether submetering is allowed, required or needs prior approval for each utility.
- How the rate charged to residents must be calculated.
- Which fees are allowed, including administrative and late fees.
- What the bill and the lease must disclose.
- How long records must be kept and how often meters must be tested.
Affordable housing adds another layer. Under the federal Low-Income Housing Tax Credit rules, utility costs paid through an actual-consumption submetering arrangement are treated as paid directly by the tenant, which affects the utility allowance. Source: 26 CFR § 1.42-10.
What goes wrong after the meters are in?
Most problems after installation are operational. A meter stops transmitting and a unit goes unread. A resident moves out mid-cycle and the reading is not captured. The total of all submeters drifts away from the master bill and nobody reconciles the two.
A sound program has a written rule for missed reads, a move-in and move-out reading for every lease, and a monthly comparison between the master bill and the sum of the submeters.
How AirBills handles it
AirBills supports true submeter billing, RUBS by square footage, occupancy or rooms, and hybrids of the two, with rules set per property. Missed reads follow a configurable fallback, such as last-known or seasonal-average, with reconciliation when the actual read arrives. A rule library by state and city helps utility teams keep each program within local requirements. See AirBills for utility admins.