← Knowledge base
Configuration5 min read

How do you configure AirBills for your company?

Set up your AirBills company profile, entities, markets, bank accounts, GL and charge codes, spike and approval thresholds, bill rules and notifications.

You configure AirBills from the Settings section of each role's sidebar. A typical setup covers the company profile, legal entities, markets, bank accounts, GL and charge codes, spike and auto-approval thresholds, bill processing rules and notifications. Most pages follow the same pattern: click Edit, change the values, then Save.

Where does each setting live?

SettingPage
Company profileProperty Manager › Settings › Company
Team membersProperty Manager › Settings › Roles
Legal entitiesAccountant › Settings › Entities
MarketsUtility Admin › Settings › Markets
Bank accountsProperty Manager › Settings › Bank Accounts, Accountant › Settings › Bank Accounts
Charge codesProperty Manager › Settings › Charge Codes
GL codesAccountant › Settings › GL Codes
Spike thresholdsUtility Admin › Settings › Spike Threshold, Property Manager › Settings › Spike Threshold
Auto-approval thresholdsAccountant › Settings › Approval Threshold
Bill checksAccountant › Settings › Bill Processing Rules
Funding top-upsSettings › Payments (Property Manager and Accountant)
Email alertsSettings › Notifications (per role)

How do you set up the company profile?

  1. Open Property Manager › Settings › Company. The page has Company, Address and Contact tabs.
  2. Click Edit.
  3. Change the name, website, business type, market, employee count, EIN and description.
  4. Edit the business and billing addresses. A checkbox copies the business address into billing. It is a one-time copy and the two do not stay linked.
  5. Edit the primary contact's name, email, phone and role.
  6. Click Save Changes, or Cancel to restore the saved values.

Every field on every tab must pass validation before saving. For example, the EIN uses the xx-xxxxxxx format and the state is two letters.

How do you add entities and markets?

Entities are the legal entities that own your homes.

  1. Open Accountant › Settings › Entities.
  2. Add an entity with its legal name, EIN and type (LLC, Corporation, Partnership or Sole Proprietorship). New entities start as Active.
  3. Edit an entity to change its name, EIN, type or status, for example to mark it inactive.

Two entities cannot share a name. Only admins can add, edit or delete entities, and deleting cannot be undone.

Markets are the cities where you run utility services.

  1. Open Utility Admin › Settings › Markets.
  2. Add a market by picking its city, state and region. A market is named "City, ST".
  3. Switch a market between active and inactive from its row.

Properties are linked to a market through their market field. Inactive markets show 0 properties served.

How do you set up bank accounts?

  1. Open Settings › Bank Accounts.
  2. Add an account with the bank name, account type, account and routing numbers and a friendly name.
  3. Link the account to entities or markets.

An account linked to entities covers the properties those entities own. An account linked to markets covers the properties in those markets. Account numbers are shown masked, with only the last four digits. Totals count active accounts only.

To keep funds available, open Settings › Payments, click Edit, turn on Low Balance Autopay, and set the balance threshold and the amount to add. When your balance drops below the threshold, that amount is pulled from your linked bank account. Accounts are set up as prepay. Changing the billing cycle goes through support.

How do you map GL and charge codes?

Codes decide which account each utility bill is booked to.

  1. Open Property Manager › Settings › Charge Codes or Accountant › Settings › GL Codes.
  2. Add a code. Choose the type (Bill Type, Biller or Property), enter what it applies to, then enter the code.
  3. Edit or delete a code from its row menu.

There are three kinds of mapping: by bill type, by biller and by property address. Bills are categorised automatically using these mappings, and the GL code shows on each bill in the payables queues.

How do you set spike and auto-approval thresholds?

Spike thresholds decide how big a jump in a bill counts as a spike. They are set per utility type, separately for empty and occupied homes.

  1. Open Utility Admin › Settings › Spike Threshold. This page holds the company defaults.
  2. Click Edit Thresholds.
  3. For each row, pick a spike percentage (10, 15, 20, 25 or 30%), set a dollar limit, and switch the row on or off.
  4. Save. An Unsaved Changes badge shows while you edit.

The same defaults appear as the auto-approval thresholds on Accountant › Settings › Approval Threshold, so saving in one place changes the other. A bill is auto-approved only when its spike percentage is at or below the threshold, its amount is at or below the dollar limit and its GL codes match. Bills that miss these limits go to Review or Flagged for a person to check.

On Property Manager › Settings › Spike Threshold you can set your own values on top of the company default. While editing, a preview shows how many existing spikes would be flagged at the new percentage. The preview uses the spike percentage only. You can reset one row or all rows back to the company default.

How do you configure bill processing rules?

  1. Open Accountant › Settings › Bill Processing Rules.
  2. Turn each rule on or off and edit its settings.
  3. Click Save, or Reset to return everything to defaults.
Rule groupWhat it catches
AmountHigh-value bills above a dollar threshold, zero or negative bills, credits that are not negative
Service periodPeriods shorter or longer than a set number of days
EntityBills tied to listed entity codes or names, and placeholder values
Invoice numberNumbers that are too long, match a bad pattern or contain whitespace
ReconciliationComputed totals that differ from the vendor total beyond a dollar or percent tolerance
Operator remindersPost date confirmation, row removal confirmation and sign-off before final funding

The rules are global. They cover every bill in a batch, not one property or biller. Rules that are turned off keep their settings.

How do you choose notifications?

Open Settings › Notifications in your role and toggle each alert.

The Spike alert uses the thresholds set on Settings › Spike Threshold.

How do you manage team members?

Open Property Manager › Settings › Roles. You see every team member with their contact details and role. Use Add User to add a teammate. From a teammate's row menu you can edit them, resend their invite or delete them. The role sets what each person can access.

How AirBills handles it

AirBills applies your thresholds, codes and rules to every bill automatically. Company defaults are shared across the Utility Admin, Accountant and Account Payables threshold pages, so one change keeps spike alerts and auto-approval consistent.

Billing That Runs Itself

Automate tenant billing, cut disputes, and reclaim hours every week.

Book a Demo